In this post, I will explain how to use RF protection to block most of the RF emitted from these meters, according to their location in or next to your house/apartment.

Please note that with or without protection, I recommend moving beds, desks, and sitting areas as far away as possible from the meters.

Before (and after) using protection, use your EMF meter to measure the RF and magnetic radiation.

In every case of using protection, it is recommended to ground it.

In addition to the RF, we can also use ELF magnetic protection to block the ELF magnetic field emitted from the meters, but take in mind that the distance the ELF magnetic field travels and its effect, is usually lower than the RF. So not in all cases I would use ELF protection.

I think that if you can OPTIONOUT for the smart meter, it is better to opt out than to use protection.

In all the cases below, we will try to put the protection between us and the meters.

The RF Protection

The RF protection should be installed between people, beds, sitting areas, and the meters.
The installation should be done in a way that reduces the RF levels measured across the house.
The installation should still allow the meter to transmit the data to the electric company (don’t rape it around with 100% protection).
Usually, the RF protection should be much larger than the meter itself.
The RF Protection should not cause any fire or electrocution hazards.

Materials:

• For protection outside the house, I usually use a metal mosquito net. It is cheap and weather-resistant.
  Using it inside the house is not recommended as it will probably add some reflections.
  The net is conductive to electricity, so don’t let it touch any electric components, wires, or accessories.
• For temporary (up to 3 months) in-house protection, I would use Mylar blankets
  Mylar – https://www.norad4u.com/order-and-buy-emf-related-products/order-from-amazon/#Emergency_Mylar_Thermal_Blankets_Pack_of_10
• For temporary (up to several years) in-house protection, I would use RF Protection Fabric like the S190
  S190 – https://www.4ehsbyehs.com/product/s190/
• For permanent in-house protection, I would use RF Blocking paint, and over it RF-blocking wall paper.
  Paint – https://www.4ehsbyehs.com/product/yshield-rf-blocking-paint/
  Wallpaper – https://www.4ehsbyehs.com/product/rf-reducing-wall-paper/

The ELF protection

For ELF magnetic protection I recommend using the help of professionals. If the material used for ELF protection is made of metal, it might also block some or most of the RF (depending on it’s size).

What not to do

Don’t use protection in away that might increase the chance of fire or electrocution.

Don’t use a metal mosquito net (or other metal) inside the house as it may add reflections.

Don’t rape the meter from all sides as you will block the data transmission.

Cases:

First case – meters in a pillar outside the house

This case is relevant mostly for EHS people.

If the pillar is close to the house, there will probably be more RF entering the house, and less if the pillar is farther away.

The first step would be to use the mosquito net on the back of the pillar.

The second step would be to put a second layer of RF protection between the pillar and the house.

Second case – meters installed on one of your house’s outside walls (on the outside)

In this case, the protection is very simple. You need to put RF (and/or ELF) protection on the inside of that wall. you can use Mylar as a temp protection, RF-blocking fabric as less temp protection and RF blocking paint+wall paper as a permanent solution

In general, in the USA and CANADA, in the case of a privet house, usually the meter is installed on a metal box. If this the case, the metal box blocks some of the RF. Some RF will still get into the house from the sides of the box. This needs to be stopped from the inside of the house, as in the picture above. Putting protection that blocks 100% of the RF, on the box outside the house can drive more RF into the house, and I think it should not be done. In case this is a house in which people are walking around the box, in the yard/garden, some week (for example 90-80% RF Blocking) protection can be installed over the box, in order to block some of the RF and limit the exposure around the box on the outside of the house. This should be done in addition to the protection inside the house against that wall.

Third case – meters installed on one of the external walls, but inside your house

This case is more problematic as the meter is inside the house. The meter should be covered (glass, wood, plastic cover), and the RF protection should be installed on the cover.

Fourth case – meter is installed on an internal wall inside your house.

This case is the most problematic. The meter is in the middle of the house.
If this is the case and you are an EHS person, I recommend moving the meter outside the house and then using protection. If you are not an EHS person, you have 2 other options:
a. Protecting the bedroom next to the meter, while leaving the kitchen and living room exposed.

b. Using RF protection both on the bedroom and partially on the side of the kitchen-living room, while leaving the protection open just a little bit so the meter could still single out.

The post RF Radiation protection for Smart Meters appeared first on www.norad4u.com.

The bag will block all reception to the phones inserted to it, and most (if not all) radiation from the phones inside it.

Product’s page – https://www.4ehsbyehs.com/product/cellphone-blocking-bag/

Video demonstration – https://youtu.be/AFmeDxtrkRs

The post NEW PRODUCT! – A Cellphone Blocker Bag! appeared first on www.norad4u.com.

I use it whenever I drive in my car. It allows me to drive longer and farther away on today’s roads of radiation.

Link – https://www.4ehsbyehs.com/product/fhc190/
Link to other hats – https://www.4ehsbyehs.com/rf-protection-hat/

Video – https://youtu.be/3bRqhQ5LF18

The post Back in stock – Full head/face Radio Protection Cover/Hat FHC190 appeared first on www.norad4u.com.

So I said I will build him a small Faraday cage in which he will be able to put his developments projects and test them at very low RF levels.

This video will show the building process of an RF Faraday cage from making the frame to putting it on the sea through protection.

Video – https://youtu.be/MDZ8PXOjGQk

The post BUILDING A FARADAY CAGE FOR TESTING RF 07 2023 appeared first on www.norad4u.com.

Easier to wash, durable and not so hot in the summer.

Video

Link – https://youtu.be/ziZ7-AsLzzg

Products page

Link – https://www.4ehsbyehs.com/product/rf-protection-color-baseball-hat-cbh190nn/

The post New product – RF Protection baseball net hat appeared first on www.norad4u.com.

Allow you to protect your body even if there is some RF in your bedroom,

Can be used as a blanket(200X140cm), a long sleeping bag(200X75cm), a wide sleeping bag (150X100cm), as upper body protection, & even as wall protection when needed.

Price – US$180

Free shipping for this item to the USA, Canada, Australia, UK, EU, and most of the world.

Link – https://www.4ehsbyehs.com/product/rf-protection-blanketsleeping-bag-2/

The post New product – RF Protection Blanket/sleeping bag appeared first on www.norad4u.com.

The post <strong>New product! – Short sleeves RF Protection Shirt</strong> appeared first on www.norad4u.com.

Fabrics

S240 https://www.4ehsbyehs.com/product/s240/
S190 https://www.4ehsbyehs.com/product/s190/
S132 https://www.4ehsbyehs.com/product/s132/
S200S https://www.4ehsbyehs.com/product/s200s/
NATURELL https://www.4ehsbyehs.com/product/naturell/
VOILE https://www.4ehsbyehs.com/product/voile/
NEW DAYLITE https://www.4ehsbyehs.com/product/new-daylite/

Other tools

Clothes: https://www.4ehsbyehs.com/protection-clothes/
Hats: https://www.4ehsbyehs.com/rf-protection-hat/
Meters – https://www.4ehsbyehs.com/emf-meters/

The post Our collection of RF Blocking Fabrics 11-2022 appeared first on www.norad4u.com.

Measuring the wall with my RF meter CORNET ED88T PLUS showed max RF levels of 3.8mW/m2. This made the storage room unusable for me for everything but storage. When ever I had to work there for several minutes, I did not fell comfortable. 2 weeks back I made my mind to fix this issue, and on this occasion also rearrange the room so it will be suitable for more than just storage.

Materials and tools:

• CORNET ED88T PLUS EMF Meter – https://www.4ehsbyehs.com/product/cornet-ed88tplus/
• RF Blocking Wall paper – https://www.4ehsbyehs.com/product/rf-reducing-wall-paper/
• S190 RF Blocking Fabric – https://www.4ehsbyehs.com/product/s190/
• Grounding strips

Steps:

1. Scanning the wall with the RF meter. Finding the Radiation penetration points.
   Then measure also in the middle of the room.

2. Grounding strips installation, I recommend installing the strips even if right now you don’t mean to connect them to the ground outside (using electric ground is not recommended).

3. Installing the wallpaper , 2 layers over the penetration points, one layer over the rest

4. wait for the wallpaper glue to dry off

5. Paint over the wallpaper with Water-plastic based paint

6. Measure the RF again, scan the wall, see how much RF is still getting in.

7. Decide if to put an additional layer of protection, and what kind.
In this case the RF levels after the wallpaper was dried off was around 0.03mW/m2.
Very nice reduction, but not enough for me.
So I decided to put an additional layer of RF protection, this time with the S190 fabric.
The S190 is very good for temp ( and in this case constant) RF protection for walls, because of its’ white color and good attenuation of RF radiation. In order to fix it to the wall, I have stitched it to the wood pools which will hold the table and shelves as well.

8. Measure the RF levels again. Scan the wall, and measure also in the middle of the room. This time the measurement over the wall showed a max level of 0.0005mW/m2,

9. Now it was time to complete the building of the new furniture, shelves and tables.

Video

https://youtu.be/B08lgnBVvdo

The post RF Protection with Wallpaper and Fabric appeared first on www.norad4u.com.